// Guides // FeNau

Press-locked or electro-forged – which type for which purpose?

At first glance they look the same, but they are made completely differently – and that determines appearance, price and use. Here is the comparison without the sales pitch, including the designations found on every delivery note.

1. Press-locked grating (P): cold-pressed, exactly square

In a press-locked grating, the bearing bars standing on edge are slotted and the cross bars (flat bar, e.g. 10 × 2 mm depending on pitch) are pressed in cold under high pressure. The result is a positively locked, flat grid with exactly square or rectangular meshes, no weld spatter and a smooth top surface. Standard pitches: 33/33 (mesh 30/30), 33/11 (30/10), 33/22 (30/20); 22/22, 44/44 and others on request.

  • Appearance: a uniform pattern, which makes it the first choice for light wells, entrances, terraces, façades and anything visible.
  • Fine pitches (33/11) can only be produced economically as press-locked gratings.
  • Made to measure: any intermediate size, cut-outs, bevels, radii – the configurator produces press-locked gratings only.

2. Electro-forged grating (SP): electrically welded, robust

In an electro-forged grating, twisted round bars or square bars are resistance-welded onto the bearing bars as cross bars under pressure and current. The cross bars sit slightly proud and the pattern is somewhat busier, but the joint is very stiff and production is faster. Typical pitches: 34/38, 34/50, 34/76, 34/100 – mostly rectangular meshes.

  • Price: cheaper per m², especially for large quantities and standard panels (1000 × 1000, 1000 × 1200 mm).
  • Use: industrial floors, walkways, platforms, wastewater treatment plants, power stations, scaffolding – wherever appearance is secondary.
  • Slip resistance: the twisted cross bars inherently give a little more grip than a smooth press-locked grating.

3. Direct comparison

CriterionPress-locked (P)Electro-forged (SP)
JointCross bar pressed cold into slotted bearing barCross bar resistance-welded onto bearing bar
Mesh patternexact, square/rectangular, flatrectangular, cross bars proud, “technical”
Fine mesh 30/10yes, standardnot usual
Load capacitythe same – determined solely by the bearing bar (height × thickness) and the bearing bar pitch
Made to measure, cut-outsvery good, any sizepossible, usually cut from standard panels and re-banded
Price per m²baseapprox. 10–25 % cheaper for standard panels
TypicalLight well, entrance, terrace, façade, data centre, swimming poolIndustry, walkway, platform, wastewater treatment plant, shelf deck
At FeNauCustom gratings in the configuratorElectro-forged gratings in the shop

4. Other types you will come across

  • Fully galvanised grating: a press-locked grating that is hot-dip galvanised completely in the zinc bath after pressing – this is our standard; all custom gratings are fully galvanised to DIN EN ISO 1461.
  • Sheet-metal plank grating: folded from perforated or slotted sheet, very light, low load capacity, for walkways and treads with small spans (sheet-metal treads).
  • Close-mesh safety grating (e.g. pitch 22/22, 11/11): for heel and wheelchair safety and above workstations.
  • Louvre grating: press-locked grating with angled louvres instead of cross bars – rain and privacy protection for ventilation (more).
  • GRP grating: glass-fibre reinforced plastic, moulded or pultruded, corrosion-free, non-conductive, but less stiff (GRP at FeNau, comparison here).
  • Aluminium grating: light, low-corrosion, lower load capacity – jetties, roof areas, plant construction (jetty gratings).

5. Reading the designation: P 33 × 33 | 30 × 2 | 1000 × 500

PartMeaning
P / SPPress-locked grating / electro-forged grating
33 × 33Pitch in mm: bearing bar spacing × cross bar spacing (clear mesh approx. 30 × 30). 33 × 11 = fine mesh 30/10.
30 × 2Bearing bar: height 30 mm × thickness 2 mm – this is the overall height of the grating and its load capacity.
1000 × 500Length × width in mm; the first dimension is always the bearing bar direction (span).
Additions“R” or “gezahnt”: slip resistance (serrated); “tz”: hot-dip galvanised; “V2A/V4A”: stainless steel (304/316); “mit Zarge”: with frame; “Ausschnitt lt. Skizze”: cut-out as per sketch.

6. DIN 24537-1 and RAL-GZ 638: the basis of manufacture

DIN 24537-1 “Gratings as flooring – Part 1: Gratings made of metallic materials” covers terms, dimensions, tolerances, proof of load capacity and marking. The RAL-GZ 638 quality and test regulations of the German grating quality association go further: defined welded and pressed joints, a deflection limit of L/200, load testing and third-party inspection. Both require a perimeter edge banding of the same height as the bearing bar and a dimensional tolerance of +0 / −4 mm for length and width. The tolerance sheet is available to download.

Questions and answers

What is the difference between a press-locked and an electro-forged grating?

In a press-locked grating, cross bars are pressed cold into slotted bearing bars (exact meshes, fine pitches possible); in an electro-forged grating, twisted cross bars are welded onto the bearing bars (cheaper, robust, technical look). In both cases the bearing bar determines the load capacity.

Which type is cheaper?

Electro-forged gratings are usually 10–25 % cheaper per m² for standard panels. For made-to-measure work, cut-outs and fine mesh, the press-locked grating is the more economical and better-looking choice.

What does P 33×11 | 30×3 mean?

Press-locked grating, pitch 33 mm (bearing bars) × 11 mm (cross bars), i.e. fine mesh 30/10, bearing bar 30 mm high and 3 mm thick.

What is a fully galvanised grating?

A press-locked grating that is hot-dip galvanised completely in the zinc bath after manufacture (DIN EN ISO 1461) – standard for all our custom gratings.

Can I also order electro-forged gratings in the configurator?

The configurator produces custom press-locked gratings. You will find electro-forged gratings in standard sizes in the FeNau shop; special sizes on request.