// Guides // FeNau
Measuring and ordering gratings correctly – the guide
90 % of all complaints about custom gratings are measuring errors: wrong direction, outer instead of inner dimension, forgotten cut-outs. With this guide it will not happen to you.
The 8 steps
- Clarify the supports. Where does the grating rest? On two opposite sides (frame, wall edge, seating frame) – these are the supports. The other two sides may be free. Each bearing bar needs 20–30 mm of bearing length.
- Set the bearing bar direction. The bearing bars run from support to support. This direction is the first dimension in the configurator (span). For light wells: well edge → house wall. For channels: across the channel. For entrances with 30/10: in the walking direction (why).
- Measure the clear dimension. Internal dimension of the frame, in two places per direction, take the smallest value. Do not deduct anything – the +0 / −4 mm tolerance to RAL-GZ 638 includes the clearance. With a frame: measure the structural opening and the frame is made to suit it.
- Check the overall height. The bearing bar height (20–60 mm) is the grating height. Does it fit the rebate? Should the grating sit flush with paving or a terrace? A support that is too high can be compensated with grating supports; one that is too low cannot.
- Choose the use. Pedestrian, car, van/lorry – the configurator determines the bearing bar from this. If in doubt, choose the higher class; details in the load guide.
- Choose mesh and finish. 30/30 for light, 30/10 for entrances and footpaths; galvanised, 304 or 316; smooth or serrated (slip resistance).
- Enter cut-outs and frame. Pipes, posts, corners, radii – see below. A frame if there is no existing surround.
- Check before ordering. First dimension = bearing bar direction? Internal dimension? Height fits? Quantity correct (measure each well individually)? Then order – the final price and lead time are shown immediately.
Cut-outs and special shapes
Cut-outs are entered in the configurator with position and size and are banded by us (perimeter banding around the cut-out) so that the grating does not lose load capacity at that point. Dimensions are always given from the edge of the grating (left/bottom), bearing bar direction first. For more complex shapes:
- Rectangular cut-out (post, duct): distance from two edges + width × length.
- Round cut-out (downpipe, column): centre point + diameter; for pipes add 10–20 mm for clearance and insulation.
- Corner cut-out, bevel, radius: a dimensioned sketch is enough – send a photo via the contact form and we will add it to the order.
- Split gratings: cut-outs at the edge or splitting into two halves let the grating be fitted around a pipe.
- Trapezium, polygon, arc: to drawing – state the bearing bar direction and we will position the banding accordingly.
Order a frame – yes or no?
| Situation | Frame? | Version |
|---|---|---|
| Plastic/concrete light well with bearing rim | no | Lay the grating directly |
| Masonry/concrete well, channel, opening in paving | yes | Angle frame for casting in (with anchors) |
| Existing concrete edge, retrofit | yes | Angle frame for bolting on |
| Trafficable | always | Anchored frame, grating secured with clips |
| Timber/steel substructure (terrace, jetty) | no | Grating on beams, with clips (fixing) |
The frame is made to suit the grating in the configurator (same material, height = bearing bar height) – standard frames are available at FeNau frames & surrounds.
What you order in the end
Your order reads, for example, P 33 × 11 | 30 × 2 | 1000 × 500 mm, hot-dip galvanised, 1 round cut-out Ø 120 mm, with angle frame. The designation is explained in the grating types guide. On request, every grating comes with a declaration of conformity to RAL-GZ 638 / DIN 24537-1 and the tolerance sheet.
Lead time, shipping, withdrawal
- Lead time: standard versions (bearing bar 25–60 mm, 2–3 mm) approx. 3–4 weeks; 20 mm bearing bar 5–6 weeks; 4–5 mm thickness and heights from 70 mm 6–7 weeks; stainless steel approx. 8 weeks – current times under delivery times.
- Shipping: parcel up to parcel size, larger items by freight forwarder on a pallet to the kerbside; details in the shipping terms. For freight deliveries, plan for unloading – a 1500 × 1000 grating with 40 × 3 weighs over 55 kg.
- Withdrawal: custom gratings are made to your specifications, so the 14-day right of withdrawal does not apply (Section 312g(2) no. 1 of the German Civil Code, BGB). The statutory warranty (2 years) applies in full – if the grating differs from the order, we remake it.
- Business customers: order on account with VAT shown; EU businesses with a VAT ID are tax-exempt. For projects with many positions: send a parts list via the form and we will set up the order.
Questions and answers
Which dimension do I enter first?
Always the bearing bar direction – the dimension from support to support (span). The second dimension is the width.
Do I need to deduct clearance?
No. Order the clear internal dimension; we manufacture to RAL-GZ 638 with +0/−4 mm and the grating is never larger than ordered.
How do I specify a cut-out?
Position from the edge of the grating (bearing bar direction first) and size or diameter. Send complex shapes as a sketch via the contact form – we add them to the order.
Can I return a custom grating?
No, the right of withdrawal does not apply to made-to-measure items (Section 312g(2) no. 1 BGB). The two-year warranty applies – if the grating differs from the order, we remake it.
How long does delivery take?
Standard gratings approx. 3–4 weeks, stainless steel approx. 8 weeks, special thicknesses 5–7 weeks; current times are on the delivery times page.