// Guides // FeNau
Gratings as house surrounds and ventilation gratings
The gravel strip around the house silts up, grows weeds and still splashes when it rains. A grating strip on a frame takes the water, keeps the façade clean, ventilates the plinth – and still looks like new after 20 years. This is how to plan it.
1. What a grating strip around the house does
- Splash protection: DIN 18533 defines the splash zone as at least 30 cm above ground level; a grating through which rain drains away immediately reduces splashing onto plinth and façade considerably compared with gravel or paving slabs.
- Drainage: water from the façade, terrace and paving reaches the drainage layer below instead of standing against the basement wall.
- Ventilation: plinths, timber façades and ventilated cladding dry out from below; the grating covers the façade's ventilation gap without closing it.
- Maintenance: no weeds, no gravel on the terrace, grating removable for cleaning the drainage.
- Appearance: a clean edge between façade and paving; galvanised, powder-coated anthracite or stainless steel on exposed façades.
2. Planning: width, mesh, bearing bar
| Feature | Recommendation | Note |
|---|---|---|
| Width | 150 – 400 mm, typically 200–300 mm | Width = span (bearing bars across the house wall, from frame to frame) |
| Length per grating | 1000 – 1500 mm | Divide each side of the house into panels, parts list with positions |
| Mesh | 30/10 (33/11) | keeps leaves, gravel and mice out, safe for heels at entrances; 30/30 only where maximum airflow counts |
| Bearing bar | 25 × 2 or 30 × 2 | easily pedestrian at a 300 mm span; design as trafficable at driveways (trafficable) |
| Material | hot-dip galvanised; 304 at entrances and exposed façades; duplex RAL 7016 to match anthracite windows | de-icing salt by the road → 316 or grit instead of salt |
| Slip resistance | smooth; serrated at entrances with a slope | grating strips are walked on – observe the R class |
3. Frame, fall, corners
- Angle frame on both sides (at the house wall and towards the paving), cast in concrete or bolted onto a concrete strip – it is the support and the clean edge. Height = bearing bar height. Frames are also available as standard frames from FeNau.
- Do not bond the frame to the façade: leave 10–20 mm to the thermal insulation or waterproofing; the grating sits above it. Never drill through the plinth waterproofing with anchors.
- Fall: top of grating 1–2 % away from the house, with a drainage layer underneath (gravel 16/32) over a drainage pipe or soakaway layer.
- Corners: external and internal corners as mitred gratings or as a corner panel with two bearing bar directions – from one parts list; we draw the layout.
- Downpipes, light wells, basement windows: cut-outs and recesses directly in the configurator; order light well gratings at the same time (guide).
- Securing: clips every 1000 mm against lifting and rattling – especially with pets and children (fixing).
4. Ventilation gratings for basement windows, air shafts and crawl spaces
Punched sheet-metal grilles dent, plastic grilles become brittle, and mice gnaw through both. A grating used as a ventilation grille is tread-resistant, gnaw-proof and has more free area:
- Vertical in the wall (basement window, boiler room supply air): grating as a grille in an angle frame, mesh 30/10 against animals; with a louvre grating also rain-protected (more).
- Horizontal in the ground (air shafts, crawl space ventilation, foundation ventilation): like a light well grating, walkable, 30/10.
- Free area: specified by heating and ventilation designers; 30/30 ≈ 80 %, 30/10 ≈ 70 %, louvre 30–50 % – choose the size accordingly.
- Insects: a grating is not an insect screen – back it with stainless steel mesh if necessary; the grating stays load-bearing and protects the mesh.
5. Heat pump: grating as base and enclosure
Air-to-water heat pumps need unobstructed air inflow and outflow and produce condensate – up to several litres a day, which turns into sheets of ice in winter. A grating as a base or as a cover over a gravel trough lets the condensate drain away, stays walkable without ice and, with a 30/30 mesh, is permeable enough for supply air from below. As an enclosure or screen around the outdoor unit, powder-coated louvre or press-locked gratings are used – observe the manufacturer's minimum clearances on the intake and discharge sides and keep the grating removable (maintenance, defrosting).
Questions and answers
How wide should the grating strip around the house be?
Typically 200–300 mm (150–400 mm possible). The width is the span; a 25×2 or 30×2 bearing bar is enough for pedestrian strips.
Which mesh for a house surround?
30/10 – keeps leaves, gravel and mice out and is safe for heels. 30/30 only where maximum airflow counts (ventilation shaft, heat pump).
Do I need a frame?
Yes, on both sides as an angle frame (cast in concrete or bolted on) – it is the support and the clean edge. Leave 10–20 mm to the plinth insulation and do not drill through the waterproofing.
Does the grating replace the gravel strip?
Yes. A drainage layer remains under the grating (gravel 16/32 over a drainage pipe or soakaway layer); the grating keeps weeds away and can be removed for cleaning.
Can I get the house surround in anthracite?
Yes, as a duplex system hot-dip galvanised and powder-coated (e.g. RAL 7016), or in stainless steel on exposed façades and at entrances.