// Guides // FeNau

Gratings on roofs and façades

Every flat roof with plant needs routes that do not wear out the waterproofing – and every façade with plant behind it needs air without views in. How roof walkways, PV maintenance routes and façade gratings are planned.

1. Maintenance walkways on flat roofs

The German flat roof guidelines and DGUV Information 201-054 (roof work) require permanent access routes to rooftop plant on roofs that are walked on regularly. A grating walkway on pedestals or frames achieves this without penetrating the waterproofing:

  • Build-up: protection mat → adjustable pedestals or heavy-duty pads → aluminium/steel section → 30/30 grating with clips. No fixings into the waterproofing.
  • Green roof: walkway 50–100 mm above the substrate, the grating lets light and rain reach the plants; edge angle to keep substrate off the walkway.
  • Gravel roof: grating on a frame in the gravel, gravel does not spill onto the walkway (frame or 30/10).
  • Weight: aluminium (8–12 kg/m²) where roof load capacity is limited, otherwise galvanised 30 × 2 (21 kg/m²); spans 600–1000 mm.
  • Drainage: the walkway must not cover outlets or emergency overflows – cut-outs or panel division over gullies, grating removable.

2. PV systems and plant rooms

  • PV maintenance aisles between module rows: grating strips 400–600 mm, aluminium, on the PV ballast system or separate pedestals; earthed to the system's equipotential bonding.
  • Ventilation and refrigeration units: maintenance platform around the unit, 1.5 kN / 5 kN/m² (toolboxes, filter changes), mesh 30/20 against screws falling onto the waterproofing.
  • Ventilation and smoke vent openings: walkable cover gratings 30/30 or louvre gratings against rain – free area according to the ventilation design.
  • Roof access: grating stair treads and landings at roof stairs, step-overs across parapets and pipe runs (treads).

3. Fall protection and wind suction

From a fall height of 2 m (ASR A2.1), railings, anchor points or a 2 m distance from the roof edge are required – route the walkway so it keeps this distance, otherwise fit railings on the substructure. Wind suction: an open grating has only a fraction of the suction load of a closed surface, but gratings on roofs are nevertheless always secured with clips and the substructure is ballasted or connected – evidence to DIN EN 1991-1-4 for rooftop structures by the designer. Never lay gratings loose on roofs.

4. Façade gratings and sun shading

  • Ventilated façades in front of plant rooms, underground car parks, transformer stations: louvre gratings with 30°–60° louvres, duplex in the façade colour or anodised aluminium – rain out, air in, views blocked (louvre gratings).
  • Brise-soleil / sun shading: horizontal or vertical louvre panels in front of glass façades, louvre angle according to the sun's position, load-bearing as a press-locked grating and walkable for window cleaning.
  • Façade maintenance balconies and escape balconies: grating 30/10, non-combustible, drainage through the surface (balcony).
  • Plinth and basement ventilation: gratings as ventilation grilles instead of sheet metal (ventilation gratings).
  • Guard panels in front of French windows (Juliet balcony) as a stainless steel grating panel – openings ≤ 12 cm, height according to the state building code.

5. Planning

  1. Check the roof load reserve with the structural engineer (walkway + people + ballast); aluminium if it is tight.
  2. Route with a 2 m distance from edges or with railings; keep gullies and rooflights clear.
  3. Panel layout to the pedestal grid (600–1000 mm), panels ≤ 25 kg for carrying through the roof hatch.
  4. Material: aluminium or galvanised; stainless steel on the coast; duplex on exposed façades.
  5. Parts list with position numbers and cut-outs (pipe runs, cable routes) – we draw it up from the roof plan.

Questions and answers

How do I lay a grating maintenance walkway on a flat roof without damaging the waterproofing?

On protection mats with adjustable pedestals or heavy-duty pads, with aluminium/steel sections on top and the gratings clipped on – no fixings into the waterproofing.

Aluminium or galvanised steel on the roof?

Aluminium (8–12 kg/m²) where the roof load reserve is tight and for panels carried through the roof hatch; galvanised steel (from 21 kg/m²) is cheaper and carries more.

Does a roof walkway have to be secured against wind suction?

Yes – always secure gratings to the substructure with clips and ballast or connect the substructure; although the open grating has low suction loads, loose panels are still not permitted.

Which mesh over ventilation units?

30/20 or 30/10, so screws and small parts do not fall onto the waterproofing during filter changes; 30/30 on pure walkways.

Can gratings serve as sun shading on a façade?

Yes – louvre gratings with 30°–60° louvres as brise-soleil, load-bearing and walkable for window cleaning, powder-coated or anodised aluminium.