// Guides // FeNau

How much does a grating cost? Price factors explained clearly

There is no single grating price: what a grating costs depends mainly on how much steel is in it and how much processing it needs. The biggest price drivers are area, bearing bar height, mesh size and material – followed by type, slip resistance, cut-outs and quantity. Here you will learn how each factor affects the price, where it pays to save and where saving gets expensive.

The short answer: weight plus processing

At its core, a grating is priced according to the material it uses. The larger the area, the taller and thicker the bearing bars and the closer the mesh, the more steel is processed – and the higher the price. On top of that come the costs of finishing (hot-dip galvanising, stainless steel, powder coating) and of anything that deviates from the standard: special sizes, cut-outs, slip resistance or special edge details.

The good news: you set most of these factors yourself. If you know which properties you really need, you will not pay for reserves you never use.

Price factor 1: dimensions and area

Area is the most obvious cost driver: a grating twice the size needs roughly twice the material. Less obvious is the span. The further the grating spans freely between two supports, the taller the bearing bars have to be – and the weight per square metre rises disproportionately.

  • Long spans make a grating more expensive twice over: more area and taller bearing bars.
  • An additional support (intermediate beam) can be cheaper than a much heavier grating for large areas.
  • Very large single gratings become heavy and unwieldy. Several smaller gratings are often easier to install and can later be opened individually.

Our guide to measuring and ordering shows how to take length, width and the bearing bar direction correctly.

Price factor 2: bearing bar height and load capacity

The bearing bars carry the load. Their height and thickness depend on the load (pedestrian, bicycle, car, lorry) and on the span. A grating for a light well in the garden needs a much smaller bearing bar than one in a trafficable yard entrance.

  • Pedestrian areas usually manage with low bearing bars and are correspondingly economical.
  • Trafficable gratings need taller and thicker bearing bars – they are heavier and therefore more expensive.
  • Oversizing costs money unnecessarily, undersizing can be dangerous. The right bearing bar height is the most economical choice.

Important: never compromise on load capacity to save money. A grating that is too weak can deflect or fail. Our guide to load capacity and structural design explains how the right bearing bar is determined.

Price factor 3: mesh size

The mesh size describes the spacing of the bearing bars and cross bars, such as 30/30, 30/20 or 30/10. The closer the mesh, the more bars the grating contains – and the more it weighs and costs.

  • 30/30 is the common standard mesh and usually the most economical solution for pedestrian areas.
  • Closer meshes such as 30/10 cost more, but are needed where small objects, heels or wheelchair wheels must not fall through or sink in.
  • Barefoot areas and public spaces often require closer meshes – here the extra cost is money well spent.

Price factor 4: material and finish

The material has the greatest influence on the price per kilogram. Hot-dip galvanised steel is the standard for outdoor use and the most economical solution. Stainless steel costs several times as much but is extremely corrosion-resistant and looks high-end. An additional powder coating raises the price compared with galvanising alone but offers any colour you like.

  • Hot-dip galvanised: the most economical all-rounder for gardens, light wells, driveways and industry.
  • Stainless steel 304 (V2A): for visible, well-kept areas and higher demands on corrosion protection.
  • Stainless steel 316 (V4A): for salt, chlorine, swimming pools, coastal locations and aggressive media – the most expensive, but the longest-lasting choice there.
  • Powder-coated: when the grating should match the colour of the façade or architecture.

When choosing the material, calculate over the service life: a cheap grating that has to be replaced after a few years in a chlorine or salt environment ends up more expensive than the right stainless steel grating.

Price factor 5: type – press-locked or electro-forged

Press-locked and electro-forged gratings differ in how they are made. Electro-forged gratings are produced industrially in large quantities and are often the cheaper solution for robust standard applications. Press-locked gratings offer more freedom with close meshes, special shapes and a visually calm surface. Which type is more economical therefore depends on the application – more on this in the guide on press-locked and electro-forged gratings.

Price factor 6: slip resistance

For stairs, ramps and wet or oily surfaces, increased slip resistance (R11 to R13) is advisable or required. It is achieved with serrated bars or special profiles and costs extra compared with the smooth version. On sloping surfaces, external stairs and work areas, this extra cost is an investment in safety that should not be cut.

Price factor 7: cut-outs, special shapes and edging

Any processing beyond a rectangle takes working time: cut-outs for pipes and columns, corner cut-outs, angled cuts or radii. Cut-outs also have to be banded so the grating stays stable and no sharp edges are left.

  • Rectangular standard gratings are the cheapest.
  • Every cut-out raises the price – so plan only those that are really necessary.
  • It is often more economical to split a grating into two at a penetration rather than placing a large cut-out in the middle.

Price factor 8: accessories, quantity and shipping

Gratings are often accompanied by fixing clips, locks or a matching support frame. Include the accessories from the start so the calculation is complete. With several identical gratings, the effort per piece falls because set-up and processing only happen once. For shipping, weight and dimensions matter: large or heavy gratings are delivered by freight forwarder.

How to save without compromising safety

  1. Set the load realistically: trafficable only where vehicles actually drive.
  2. Choose the standard 30/30 mesh if no closer mesh is required.
  3. Hot-dip galvanised instead of stainless steel if there is no aggressive environment or special appearance required.
  4. Shorten spans, for example with an intermediate beam for large areas.
  5. Keep cut-outs to a minimum or replace them with split gratings.
  6. Group identical sizes: several identical gratings are cheaper per piece.
  7. Measure precisely: wrong dimensions are the most expensive mistake, because a custom grating cannot be made to fit.

Where saving gets expensive

  • Bearing bars that are too low: deflection, rattling or, in the worst case, failure.
  • The wrong material in salt, chlorine or chemical environments: premature corrosion and replacement.
  • No slip resistance on stairs and ramps: risk of accidents and liability issues.
  • No fixing: gratings can slip, rattle or be lifted out.

Calculate the exact price in a few minutes

Because every grating is made from your specifications, the quickest way to a binding price is our configurator: enter dimensions, mesh, bearing bar, material and cut-outs – and the price is shown immediately. If you are unsure about load capacity or material, we will be happy to advise you before you order.

Questions and answers

How much does a grating cost per square metre?

The price per square metre depends mainly on the weight, i.e. bearing bar height, bearing bar thickness and mesh size, and on the material. A light, hot-dip galvanised grating with standard mesh is considerably cheaper than a trafficable grating with a close mesh or a stainless steel grating. The configurator shows the exact price for your dimensions immediately.

Why is a stainless steel grating so much more expensive?

Stainless steel is more expensive as a raw material and more demanding to process than structural steel. In return, it is corrosion-resistant without any additional coating. In swimming pools, on the coast or with chemicals, it is often the more economical solution over its service life.

Is a trafficable grating much more expensive than a pedestrian one?

Yes, because it needs taller and thicker bearing bars and therefore contains much more steel. So choose the trafficable version only for areas that vehicles actually drive on.

Do cut-outs in a grating cost extra?

Yes. Every cut-out has to be cut and banded. A few well-planned cut-outs or split gratings keep costs down.

Are special sizes more expensive than standard sizes?

Custom gratings are produced to your specifications. What determines the price is less the special size itself than the area, weight and processing. Measuring precisely is important, because a custom grating can hardly be adjusted afterwards.

How do I find the cheapest suitable grating?

First set the load and span, then choose the standard mesh and hot-dip galvanised steel unless there is a reason not to. With these details the configurator gives you the price – if in doubt, our advisers will help.